![]() ![]() ![]() So the traffic on port 80 doesn't make it to the Tivo N-Adapter setup wizard but the traffic is directed to the router port 80 instead. Somehow, when setting up the VLAN and route below, I've pointed 192.168.10.1 to 192.168.1.1. My question is w hat VLAN the switches will use to transmit the LACP messages? In general, what VLAN the switches will use to transmit the protocol messages? For example, for LACP there are LACPDUs, for STP there are BPDUs.Results so far: By adding VLAN and route, when I enter 192.168.10.1, I get the Verizon Router login page (same as if I entered 192.168.1.1) instead of the browser page on the Tivo N-Adapter (192.168.10.1). Now if you do want to pass any traffic or message from VLAN 1 just do (no untagg port number or the trk group no ) on VLAN Sahil, By default all the ports assigned to VLAN 1 and they will use this VLAN to pass the traffic and messages, if you have other VLANs as well on the same port the traffic and message will pass from all the VLANS.īasically when the traffic come out from the switch it will either have untagg or tagg frame added to it. Like i mentioned there is no concept of native VLANS, if the ports the assigned to the VLANs it will pass the traffic and protocol messages. ![]() What VLAN these messages will travel over? My question is w hat VLAN the switches will use to transmit the LACP messages? In general, what VLAN the switches will use to transmit the protocol messages? For example, for LACP there are LACPDUs, for STP there are BPDUs. Right now VLAN 100 is my management VLAN because I use this VLAN for accessing the switches by CLI, but it is not configured as management-VLAN (I have to read about this feature). When you will do "show VLAN port trk (trunk group no or interface no) detail if will give you the exact VLANS assigned to a trunk group or interface. Note: If you will delete the trunk group the ports which were assigned to it will get removed from the other VLANs and get assigned to the VLAN1 as per the desgin of architecture. The moment you put the ports in a trunk group you will no longer be able to use the ports individually, you will have to use the trunk gruop. If you will check the switch configure on VLAN if that Trk group is not assigned to any other VLAN then only above mentioned VLANs will pass the traffic. What VLAN the switches will use to transmit the LACP messages? Think of a situation as mine where two switches are connected each other with a LACP link aggregation, and this link aggregation has only tagged VLANs (100, 200, 300, etc.). I remember that Cisco uses the native VLAN for the messages of some protocols, I don't know if this happens in Aruba as well. That's clear, the question then if VLAN 1 is used for some protocols such as LACP or STP. I remember that Cisco uses the native VLAN for the messages of some protocols, I don't know if this happens in Aruba as Mathew, Switch(config)# management-VLAN (VLAN ID).// just make sure OOBM is disable on the switch as both will will not work simaultaneously// If there is nothing connected or no ports assigned to a VLAN if will not work for any protocol. We don't have any concept of native VLAN unless or untill the ports are assigned to a particular VLAN and the VLANS are up they will pass the traffic. Now, if you will make any other VLAN as a management VLAN then in that case you cannot access the switch with anyother VLAN and this new management will not not pass any data traffic. After this custom settings, the new VLAN will be the PVID of the port. If you set the new VLAN as tagged, you will permit the VLAN 1 to pass untagged and the new VLAN to pass tagged. After this, only this new VLAN will be forwarded in the port. In your case you have to assign a new VLAN to the port you want, and set it as UNTAGGED. Like you mentioned above that you want to use the VLAN100 as a management VLAN and wants to remove the VLAN1.Īs VLAN 1 is the default VLAN, which means that it cannot be removed or deleted.
0 Comments
Leave a Reply. |